Base
Full Name | muhammad jawad |
Organization | uet taxila |
Job Title | researcher |
Country |
Forum Replies Created
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
You may find the simulation file .osd in introductory tutorials as well.
regards
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Dear Mohammad
If you are using an older evaluation version than optisystems 16 e.g optisystem 14, then download a newer version like 15 or 16 and your project file will be opened in both of these versions i.e 15 and 16
regards
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
I also also understand that Mr Adnan is asking about how to design logic gates using nonlinear effects. The answer of Sir Ahmad is appropriate. For instance, an all-optical inverter is easily can be implemented using XGM in SOA. A lot of literature can be found easily using digital libraries.
regards
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Dear sir,
i have sent the project file at your email address. Looking forward something great as before
regards
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Dear Josh
Thanks for imparting good relevant information regarding chaotic laser. Can we have your email address.?
regards
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
ok sir thanks
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Sir i have drawn a LI curve at 1 Gbps data, Modulation peak current =10mA, Bias current sweeps from 0 to 25mA. I gets a circular type curve as shown in Fig attached. How to get a linear straight curve like DML laser so that VCSEL can be biased at middle of this linear region?
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Please sir tell me, in order to operate VCSELs like DMLs, we have to find its LI characteristics curve and then bias it at the half of the middle point of the LI curve?
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Dear Sir
Thanks for your reply. As i have worked over optical communication over multimode fiber (MMF), i just need to know how to mathematically write LP modes in MMF. The optiwave tutorials well explain working over MMF but not give required information. If you have relevant literature, do share with me sir.
I will be very thankful
Regards
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Thanks Sir
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Thanks Sir
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
Thnx sir ahmad
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
ok sir thanks for everything
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
thanks sir, i understood it fully
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/819/5922625c8c250-bpfull.jpg)
If PRBS is set at 10Gbps with Probability checked, then what will be selection of clock at DEMUX side?