Base
Full Name | ahmed helmy teama |
Organization | Telecom Egypt |
Job Title | Research |
Country |
Forum Replies Created
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
the osd file as attached
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Dear Damian,
I changed the sequence length from 164 bits to 256, buy there is no change in results in both versions.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Sorry the attached file missing
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
yes, alistu. I understood what you mean. Also i wondered, but it is happened with me.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Thank you sam sung.
Thank you alistu.
I found the problem that i ran system established by optiwave v.7 in optiwave v.13, but when i established the same system by optiwave v.13 component it works fine.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Thank you Alistu
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
the attached file for FSO using PIN photo diode,by run the simulation the program is stuck.
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Dear All,
Dear Damain,
Could you please help me to resolve the error in my simulation that call matlab program to establish negative exp Channel in free space optical communication, as the attached m and osd files.
Hope your support.
Regards,
Ahmed
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Gurpreet Kaur, in addition you should observe From eye diagrams, the value of Q factor and Minimum BER are taken up to BER < 10-9 to achieve an error free communication, as this is the limit up to which successful communication can take place.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Abhishek Shrama
kindly find the attached paper, i think it will help you a lot
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Thanks Damian, but i can’t open the osd file, could you please send it to me via my my e-mail(ahmed.teama@te.eg)
yours,
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
May be the program didn’t installed correctly, try to remove it and install again.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
for example of using co simulate matlab with optisystem you can a look at:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Dear Damian,
Are You find the attachment, kindly i need your advice.
Thanks
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/3241/85c67071e60b491cc155edfe5ef7524c-bpfull.jpg)
Dear Damian,
Kindly fine the attached files(osd and m file) herewith our simulation that doesn’t work
thank you
yours,