Forum Replies Created

    #28860
    Profile Photo
    Yahaya Idriss
    Participant

    Ok Thanks for the information.

    #28844
    Profile Photo
    Yahaya Idriss
    Participant

    Thanks you. Can I find any component in optiSystem that can convert dBm to dB loss. I want to add in dBm to dB in the FSO component as an attenuation factor. For instance equivalent of -21.76dBm in dB loss.
    Thanks

    #28837
    Profile Photo
    Yahaya Idriss
    Participant

    Ok Thanks for your contributions. I think practically commercial white-LEDs cannot go beyond 10m although it depends on the power of the LED.
    Thanks

    #28831
    Profile Photo
    Yahaya Idriss
    Participant

    Hi Alistu
    what I expect is a drastic change in BER as the transmission distance is varies. for instance like from 2.3789e-009 to 9.1276e-009 of 3567e-008 not just 1.3667e-009 to 1.2678e-009 which is negligible cannot be shown on the graph.
    Thanks

    #28822
    Profile Photo
    Yahaya Idriss
    Participant

    Hi Alistu
    Find the shortcut were Geometric Loss box unchecked was discussed by Damian marek. https://optiwave.com/forums/topic/awgn-noise/
    Actually I intend to use bit rates of 622Mbps to analyzer the performance of both indirect sunlight and Fluorescent lamp individually as attenuation factors on indoor communication channel. The BER analyzer will be use to evaluate out how far this signal can go without any degradation, i.e transmission distance cover.(by plotting a graph of BER against transmission distance). I hope you have get the gist of this project.
    Thanks

    #28815
    Profile Photo
    Yahaya Idriss
    Participant

    Hi Alistu
    I am back again. I have increased the input power of the LED and there is improvement but I find out that there is increase in optical power after passing through the FSO component. Therefore, according to Damian marek he made mentioned in the forum on the topic of AWGN noise where he suggest that the geometrical Loss box in the FSO component should be unchecked. I did so and the problem of increase optical power is solve. However, the result at the BER change very little even when you increased the distance and change the background noise at the AWGN channel. Ideally, in VLC small change in distance like 1m to 2m supposed to show a great change at the BER. Kindly help me to rectify this problem.
    Thanks for sparing your time in assisting me.

    #28812
    Profile Photo
    Yahaya Idriss
    Participant

    Hi Alistu
    Thanks for the observation. so you mean I should not use in-line optical amplifier?. Generally you are saying that the system has low input optical power from the LED. I will try to implement your suggestion to see the impact.
    Thanks for your assistance.

    #28795
    Profile Photo
    Yahaya Idriss
    Participant

    Find attached my project file. I want to integrate both the indoor VLC system and OCDMA using the attached file with an ambient light as AWGN.
    I learned from the forum that I can unchecked the geometric loss in the FSO so that the output power signal will not be amplified, but then the signal cannot go beyond 1m if all loss are added. The BER analyzer result is always 1.
    Thanks for your assistance.

    #22185
    Profile Photo
    Yahaya Idriss
    Participant

    Dear Ravil and Sam Sung
    Thank you all for the Information. I am Sorry I was offline for sometime. I will visit the links.
    I am grateful

    Thanks
    Yahaya Idriss

    #21212
    Profile Photo
    Yahaya Idriss
    Participant

    Dear Damian
    Thanks for you suggestions.
    Please can you kindly check my simulation setup if I am doing the correct thing. The overview is to setup Indoor VLC link with OCDMA to suppressed an ambient light noise on the FSO Channel. I attached the simulation file for your perusal.
    Thanks.
    Yahaya Idriss