Base
Full Name | NGUYEN KHAC BINH |
Organization | Chonnam National University |
Job Title | Engineer |
Country |
Forum Replies Created
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Thanks for your answer.
I want to generate the broadcast signal as shown in Picture 1 using LD Source instead of using the White light source.
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Ahmad Atieh,
Could you tell me how to create a light source using an FP laser to transmit a signal to the FBG sensor? thank you.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
I want to simulate the monitoring system using the FBGs sensor in PON. Thank you for your help.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Thank you for your reply, but I do not see the LD Source in the Optical Sources as in the attached picture. Can you help me again? thanks.
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Ahmad,
Thanks for your notice, if I have any comment on the new release, I will send to you an email.
Regards,
BINH
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Thanks for your answering.
Can you explain to me about remain parameters such as Max.Q Factor, Eye Height, Threshold, and Dispersion Inst?
Regards,
Binh
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Thanks for your answering.
If you know can you explain to me about the values ​contained in the attached image?
And I want to know more about Min.BER. It should is how be good? In Figure, Min.BER is 0, I think this is not real.
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Thank you !
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Thank you so much !
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Shaymaa
Thank you for your answer, but I want to design a simulation with a Burst Modulator at 2 Kbit/s bit rate, while the layout is 1 Gbits/s bit rate. I tried to design but I cannot it. The simulation only works when the bit rates of Layout and Burst Modulator are equal or the difference is not too large. can you help me? thanks!
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Mohamed Abouseif,
Could you send me the file.zip again, or you can send me via nkbinh007@naver.com, thank you so much!
Binh
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Mohamed Abouseif,
Thank you so much! But I can not open this file, can you help me one more time, please?
Binh
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Mohamed
Thank you for your help.
I have designed a BEN with 1ns width, how to set it to 1um, can you help me, please ?
BINH
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Mohamed Abouseif
Thank you for your enthusiastic help.
I used two splitter/combiner, but the return signal does not pass the Optical Delay, do you know why?
BINH
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/31899/5b10fe6cc18f7-bpfull.jpg)
Hi Mohamed Abouseif
Thank you for your replying, if using Bidirectional type then the signal after passing through Splitter Bidirectional disappears
BINH