Base
Full Name | NURUL HAMIDA |
Organization | universiti teknologi malaysia |
Job Title | student |
Country |
Forum Replies Created
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi Sara..
Ok, I see.
Then, what kind of signal that you use for every channel, I mean such as WiFi signal or modulation signal or anything else?
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hello Sara
I would like to ask you.
How you differentiate CO OFDM signal for each channel.
It’s in terms of cyclic prefix or no pf subcarrier or others?
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi, Marc…
When I decrease the number no samples, the result shows an improvement. But, I’m still don’t know how to pick the exact value of no of samples. Can you help me?
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi Marc Verreault
But I’m still confusing about the black rectangle in the up and down of the eye diagram.
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Down here are the design set up and the output of eye diagram at back to back (BTB) and at receiver (RX)
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi, Marc Verreault…
Sorry for all the errors
Since the file exceeded the maximum file size allowed, I’m just giving the snapshot of the eye diagram result
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi, Marc Verreault.
Now I’ve understood it..
Thanks a lot.:)
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi, Marc Verreault…
Since the file exceeded the maximum file size allowed, I’m just giving the snapshot of the eye diagram result.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Thanks Naba krushna Sabat…:)
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi Naba krushna Sabat..
Ok, right now i know about one of the OptiSystem 7 behaviour. Indeed, i am using Optisystem 7.
Thanks.
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi Damian Marek,
Is there any threshold for sine wave?
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Hi K. Esakki Muthu.
I have checked the bit rate. The PRBS bit rate was same with global bit rate. The result that I got as attached down here.
Attachments:
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
I have using OptiSystem 7 and Windows 7. But, the project browser are disabled
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
In the simulation, how do we know that the component is attached to the voltage or current source?. The sine generator component parameter did not mention to choose voltage or current. Currently, I am using OptiSystem 7.0
![Profile Photo](https://optiwave.com/wp-content/uploads/avatars/18519/58eae2690c1b4-bpfull.jpg)
Thanks a lot Damian Marek…:)