Optiwave software can be used in different industries and applications, including Fiber Optic Communication, Sensing, Pharma/Bio, Military & Satcom, Test & Measurement, Fundamental Research, Solar Panels, Components / Devices, etc..
OptiSystem is a comprehensive software design suite that enables users to plan, test, and simulate optical links in the transmission layer of modern optical networks.
OptiSPICE is the first circuit design software for analysis of integrated circuits including interactions of optical and electronic components. It allows for the design and simulation of opto-electronic circuits at the transistor level, from laser drivers to transimpedance amplifiers, optical interconnects and electronic equalizers.
OptiFDTD is a powerful, highly integrated, and user friendly CAD environment that enables the design and simulation of advanced passive and non-linear photonic components.
OptiBPM is a comprehensive CAD environment used for the design of complex optical waveguides. Perform guiding, coupling, switching, splitting, multiplexing, and demultiplexing of optical signals in photonic devices.
The optimal design of a given optical communication system depends directly on the choice of fiber parameters. OptiFiber uses numerical mode solvers and other models specialized to fibers for calculating dispersion, losses, birefringence, and PMD.
Emerging as a de facto standard over the last decade, OptiGrating has delivered powerful and user friendly design software for modeling integrated and fiber optic devices that incorporate optical gratings.
Modal analysis is a pivotal component of modelling optical structures. OptiMode serves as a robust CAD platform for the design and modal analysis of waveguide structures.
Optiwave software can be used in different industries and applications, including Fiber Optic Communication, Sensing, Pharma/Bio, Military & Satcom, Test & Measurement, Fundamental Research, Solar Panels, Components / Devices, etc..
OptiSystem is a comprehensive software design suite that enables users to plan, test, and simulate optical links in the transmission layer of modern optical networks.
OptiSPICE is the first circuit design software for analysis of integrated circuits including interactions of optical and electronic components. It allows for the design and simulation of opto-electronic circuits at the transistor level, from laser drivers to transimpedance amplifiers, optical interconnects and electronic equalizers.
OptiFDTD is a powerful, highly integrated, and user friendly CAD environment that enables the design and simulation of advanced passive and non-linear photonic components.
OptiBPM is a comprehensive CAD environment used for the design of complex optical waveguides. Perform guiding, coupling, switching, splitting, multiplexing, and demultiplexing of optical signals in photonic devices.
The optimal design of a given optical communication system depends directly on the choice of fiber parameters. OptiFiber uses numerical mode solvers and other models specialized to fibers for calculating dispersion, losses, birefringence, and PMD.
Emerging as a de facto standard over the last decade, OptiGrating has delivered powerful and user friendly design software for modeling integrated and fiber optic devices that incorporate optical gratings.
Modal analysis is a pivotal component of modelling optical structures. OptiMode serves as a robust CAD platform for the design and modal analysis of waveguide structures.
Hai…
I need to know whether my simulation setup is correct …..I’m providing equal power to wire and wireless service simultaneously also using FBG for both the service……For wired service i have used OFDM demodulator but for wireless service i just used PIN,and LPF…..I got min BER and eye diagram for wired service….but not able to get for the wireless service….plz check my simulation setup which i have attached with this below…..
I’ve had problems with Optisystem v.12 OFDM blocks too. That’s probably what causes the problem. Please Take a look at the posts made by Damian on the link I gave you.
Thanks………….For wireless accesss i have been using Optical heterodyne….my demodulator is ofdm demodulator…..but i can,t get the BER and eye diagram…here i have attached my wireless section at receiver side.
I’ve mentioned this to other users here, but I see that you are using the OS 12 OFDM components, which we kept in OptiSystem 13 for our users. The new OFDM components are highly recommended as they make using them much easier.
As a side note, if you click the OS 12 OFDM Demodulator and then press CTRL+F the component will be oriented in the right direction.
Hi Sobana a!
BER is the ratio of “the number of bits in error” divided by “the total number of bits”.
therefore its minimum value of the BER can be zero and maximum value can be one.
.
