Project MODB_ModulationSystem.osd (Figure 1) demonstrates a system that is an is optical modified duobinary RZ transmission system, which is equivalent to a duobinary carrier suppressed.
Figure 1 – Modified duobinary system
Categories
OptiSystem Manuals
- OptiSystem Tutorials
- Introductory Tutorials
- Lesson 1: Transmitter — External Modulated Laser
- Lesson 2: Subsystems — Hierarchical Simulation
- Lesson 3: Optical Systems — WDM Design
- Lesson 4: Parameter Sweeps — BER x Input Power
- Lesson 5: Bidirectional Simulation — Working with Multiple Iterations
- Lesson 6: Time-Driven Simulation — Working with Individual Samples
- Lesson 7: Optical Amplifiers — Designing Optical Fiber Amplifiers and Fiber Lasers
- Lesson 8: Optical Systems — Working With Multimode Components
- Optical Transmitters
- Optical Transmitters
- LED Modulation Response
- Semiconductor Laser Modulation Response
- Semiconductor Laser—Large Signal Modulation
- Chirp in Mach-Zehnder Lithium Niobate Modulators
- LED Spectral Distribution
- Semiconductor Laser L-I Curve
- Laser Noise and Linewidth
- Vertical-Cavity Surface-Emitting Laser – VCSEL Validation
- Using the Laser Measured Component
- Optical Fibers
- Effects of Group Velocity Dispersion (GVD) on Gaussian Pulse Propagation
- Effects of PMD on Pulse Propagation
- Effects of Cross Phase Modulation (XPM) and Four-Wave Mixing (FWM)
- Combined Effects of GVD and SPM on Gaussian Pulse Propagation
- Combined Effects of GVD and SPM on Modulational Instability
- PMD-Induced Broadening of Ultra-Short Pulses
- Validation of FWM Effect
- Stimulated Raman Scattering
- Stimulated Raman Scattering—Separated Channels
- SPM-Induced Spectral Broadening
- XPM-Induced Asymmetric Spectral Broadening
- Kerr Shutter
- Bidirectional Fiber and Raman Design
- Optical Receivers
- Modulation Formats
- Extracting the Thermal Noise Parameter for a Specific Receiver Sensitivity
- Receiver Noise—PIN
- Receiver Noise—Shot Noise Enhancement with APD
- Receiver Sensitivity—Bit Error Rate (BER)
- Receiver sensitivity—Minimum input power
- Sensitivity degradation—Extinction ratio
- Signal degradation – Jitter
- Electrical PLL
- Doped Optical Fiber Amplifiers (PT1)
- Analysis of Gain and Noise in Erbium doped fiber
- Optimizing the EDFA gain for WDM lightwave systems
- Excited state absorption impact on EDFA performance
- Ion-ion interaction effects
- Rayleigh backscattering in EDFA
- Inhomogeneous broadening in EDFAs
- Power transients in EDFAs
- Temperature dependence in EDFA
- Ytterbium-doped fiber amplifiers
- SPO optimization—System margin
- Doped Optical Fiber Amplifiers (PT2)
- Doped Optical Fiber Amplifiers (PT3)
- Raman Amplifiers
- SOA Amplifiers
- SOA Gain Saturation – Gaussian Pulses
- SOA Gain Saturation – Comparison with Experimental Results
- SOA Gain Saturation – Chirped and Super Gaussian Pulses
- SOA Gaussian Pulse – Gain Recovery
- SOA Pulse Compression
- SOA as a Wavelength Converter (FWM)
- SOA as a Wavelength Converter (XGM)
- SOA In-Line Amplifier
- Wideband SOA Characterization
- Wavelength Conversion in a Wideband SOA
- Improved Gain in High-Concentration Er3+/Yb3+ Waveguide Amplifiers
- Dispersion Management
- Dispersion Compensation Schemes – A System Perspective
- Compensation of Dispersion With Ideal Dispersion Component
- Compensation of Dispersion with Fiber Bragg Grating Component
- Uniform Fiber Bragg Grating as a Filter
- Compensation of Dispersion with OptiGrating
- Dispersion Compensation Using Subsystems
- Maximum-Likelihood Sequence Estimation (MLSE) Equalizer
- DFE – Decision-Feedback Equalizer
- Dispersion Compensation Using Electronic Equalization
- Lightwave Systems
- Lightwave System Components
- Optimizing Power and Dispersion Compensation for Nonlinear RZ Transmission
- 10 Gb/s Single Channel Transmission in Standard Mode Fibers (SMF)
- 40 Gb/s Single Channel Transmission in Standard Mode Fibers (SMF)
- Engineering the Fiber Nonlinearities and Dispersion
- System Design – Power Budget
- Time Division Multiplexing (TDM)
- Broadband Optical System Based on a Passive Optical Network (BPON)
- Optical Code-Division Multiple-Access System (OCDMA)
- Free Space Optics (FSO)
- Coherent Optical Transmission
- Radio Over Fiber (RoF)
- Optical Time Domain Multiplexing (OTDM) Design
- System Performance Analysis Using Script Automation
- BER Calculation Using the BER Test Set
- WDM systems
- Comparison of RZ and NRZ Modulation Formats for 40 Gb/s Systems
- 16 Channel WDM System Design
- WDM Components – Tunable Filters
- WDM Components – AWG Demultiplexer
- Broadcast Star Coupler
- Optical Cross-Connects
- Configurable Optical Add-Drop Multiplexer
- Advanced Modulation Formats
- Conventional Duobinary Transmitter
- Modified Duobinary Transmitter
- Interferometer Characterization
- Solitons and Soliton Systems
- Fundamental and Higher Order Solitons
- Interactions of Optical Solitons
- Decay of Higher Order Solitons in the Presence of Third-Order Dispersion
- Decay of Higher Order Solitons in the Presence of Intrapulse Raman Scattering
- Decay of Higher Order Solitons in the Presence of Self-Steepening
- Stability of solitons in birefringent optical fibers
- Orthogonal Raman gain
- Average Soliton Regime
- SOA as In-line Amplifier in Soliton Communication Systems
- Metro Systems
- Digital Modulation
- CATV
- Multimode
- Cosimulation
- Introductory Tutorials
FBG Fiber Loop Mirror Sensor Design Basics
September 26, 2018
Fiber loop mirror configurations have been used in several different applications. One important application is sensing. Inserting a Fiber Bragg Grating (FBG) in the fiber loop mirror allows exploiting the switching feature of the loop mirror to enable enhanced sensing and accessing capabilities.
Evaluations
Get access to all our software tools instantly! No need to speak with a sales representative.